Float Switches & Level Control · Global Supply E-mail: szace@foxmail.com
Industrial Control › FLOAT SWITCH

UK Ball Float Level Controller, 2 m Cable

UK type ball float level controller — stainless steel ball float driving a sealed relay body, versions UK-01 / UK-02 / UK-03, explosion-proof class 1 MPa, IP68, level or vertical mounting.

  • Industrial Control › FLOAT SWITCH: Industrial Control › FLOAT SWITCH
  • Model: 9006
  • Brand / OEM: ELEHPD — OEM branding available
  • Export: Worldwide, FOB Ningbo / Shanghai
Request a quotation for this float switch

About the product — UK Ball Float Level Controller, 2 m Cable

The UK Ball Float Level Controller, 2 m Cable is part of the ELEHPD float switch range, manufactured in Yueqing, Zhejiang, China and supplied factory direct to distributors, wholesalers and panel builders. ELEHPD float switches are used in tanks, pits, sumps, sewage water and pump control, and are built to IEC/EN standards with CE marking.

The UKY series is the workhorse cable float switch and the basis of the ELEHPD float switch range. A moulded polypropylene body carries a steel ball and a sealed microswitch; as the liquid rises the float tilts and the circuit switches, starting or stopping a pump, opening a valve or raising an alarm. The float hangs from a flexible PVC or HO7RN-F cable with a polypropylene counterweight, and the switching level is set simply by sliding the counterweight along the cable — one screw, no tools. Rated 250 V AC with 380 V maximum isolation, or 120 V AC for 110/120 V export markets, in 16 A (8 A), 10 A (8 A) or 10 A (4 A) versions; protection IP68CS for permanent immersion; working temperature 0 C to 80 C with the product rated to 70 C; mechanical endurance over 100,000 cycles and electrical endurance over 50,000 cycles. Five float shapes (trapezium, rectangle, large circular, small circular, ellipse) and five body colours (red, yellow, blue, grey, black) can be ordered, and the 3-core black / blue / brown cable gives both pump-down and pump-up wiring from the same float. ELEHPD factory direct, for clean water, wastewater, mild acid and alkali, and light industrial process duty. The UK type ball float level controller follows the true liquid level instead of a float angle: a stainless steel ball rides on the surface and drives a sealed relay body, so the switching point is not affected by the density of the liquid or by foam. Three versions are available — UK-01, UK-02 and UK-03 — covering actuation ranges of 10 A, 25-550 A and 8-1000 A, with no regulation, step regulation or continuous regulation of the switching point. The body is a sealed metal relay housing rated to 1 MPa explosion-proof class with a 150 C dielectric temperature, so it can be mounted in an open or a closed vessel, at level or vertically.

Typical applications

Automatic pump control and level alarm in water tanks, cisterns, water towers, swimming pools, wells, sumps and sewage pits, plus light process vessels in food and drink, textile, chemical and metal finishing. Use the black-and-blue pair for drain-down pump control and the black-and-brown pair for fill-up. Pumps above 750 W / 1 HP and any three-phase motor must be driven through an AC contactor coil (A1/A2) — the float switch only provides the control signal. Common in water towers, cisterns and industrial process vessels where a true liquid level, rather than a float angle, is wanted.

Specifications:

Product typeBall float + relay
Switch typeSS ball float
VersionsUK-01/02/03
Level settingNone/step/cont.
Rated voltage250 V AC (380 V max) / 120 V AC
Rated current10 A (8 A) at 250 V / 10 A (4 A) at 380 V
ProtectionIP68
Working temperature0-70 C
Explosion-proof class1 MPa / 150 C
MountingLevel / vertical
BodySealed metal relay
Cable length2 m

How to specify the right float switch

When specifying, give us the rated current, the breaking capacity, the number of output points, the switching voltage and current, the mounting method and the cable length. Our engineers will select the matching model for your specification or against a sample.

Pumps above 750 W / 1 HP and any three-phase motor must be driven through an AC contactor coil (A1/A2) — the float switch only provides the control signal.